SBC-sig/scripts/bin/rockchip/wireless/system/etc/firmware/nvram_ap6181.txt

#AP6181_NVRAM_V1.2_05242017
#adjust PA parameter for g/n mode
manfid=0x2d0
prodid=0x492
vendid=0x14e4
devid=0x4343
boardtype=0x0598

# Board Revision is P307, same nvram file can be used for P304, P305, P306 and P307 as the tssi pa params used are same
#Please force the automatic RX PER data to the respective board directory if not using P307 board, for e.g. for P305 boards force the data into the following directory /projects/BCM43362/a1_labdata/boardtests/results/sdg_rev0305
boardrev=0x1307
boardnum=777
xtalfreq=26000
boardflags=0xa00
sromrev=3
wl0id=0x431b
macaddr=00:90:4c:07:71:12
aa2g=1
ag0=2
maxp2ga0=74
cck2gpo=0x2222
ofdm2gpo=0x66666666
mcs2gpo0=0x7777
mcs2gpo1=0x7777
pa0maxpwr=56

#P207 PA params
#pa0b0=5447
#pa0b1=-658
#pa0b2=-175<div></div>

#Same PA params for P304,P305, P306, P307

pa0b0=5447
pa0b1=-607
pa0b2=-160
pa0itssit=62
pa1itssit=62


cckPwrOffset=5
ccode=0
rssismf2g=0xa
rssismc2g=0x3
rssisav2g=0x7
triso2g=0
noise_cal_enable_2g=0
noise_cal_po_2g=0
swctrlmap_2g=0x04040404,0x02020202,0x02020202,0x010101,0x1ff
temp_add=29767
temp_mult=425
temp_q=10
initxidx2g=45
tssitime=1
rfreg033=0x19
rfreg033_cck=0x1f
cckPwrIdxCorr=-8
spuravoid_enable2g=1
documents and scripts for RPi and Rockchip 2024-10-25 17:48:08 +08:00			`#AP6181_NVRAM_V1.2_05242017`
Fix some simple errors Signed-off-by: lixiang <lixiang_yewu@cmss.chinamobile.com> 2024-11-20 01:00:56 +00:00			`#adjust PA parameter for g/n mode`
documents and scripts for RPi and Rockchip 2024-10-25 17:48:08 +08:00			`manfid=0x2d0`
			`prodid=0x492`
			`vendid=0x14e4`
			`devid=0x4343`
			`boardtype=0x0598`

			`# Board Revision is P307, same nvram file can be used for P304, P305, P306 and P307 as the tssi pa params used are same`
			`#Please force the automatic RX PER data to the respective board directory if not using P307 board, for e.g. for P305 boards force the data into the following directory /projects/BCM43362/a1_labdata/boardtests/results/sdg_rev0305`
			`boardrev=0x1307`
			`boardnum=777`
			`xtalfreq=26000`
			`boardflags=0xa00`
			`sromrev=3`
			`wl0id=0x431b`
			`macaddr=00:90:4c:07:71:12`
			`aa2g=1`
			`ag0=2`
			`maxp2ga0=74`
			`cck2gpo=0x2222`
			`ofdm2gpo=0x66666666`
			`mcs2gpo0=0x7777`
			`mcs2gpo1=0x7777`
			`pa0maxpwr=56`

			`#P207 PA params`
			`#pa0b0=5447`
			`#pa0b1=-658`
			`#pa0b2=-175<div></div>`

			`#Same PA params for P304,P305, P306, P307`

			`pa0b0=5447`
			`pa0b1=-607`
			`pa0b2=-160`
			`pa0itssit=62`
			`pa1itssit=62`


			`cckPwrOffset=5`
			`ccode=0`
			`rssismf2g=0xa`
			`rssismc2g=0x3`
			`rssisav2g=0x7`
			`triso2g=0`
			`noise_cal_enable_2g=0`
			`noise_cal_po_2g=0`
			`swctrlmap_2g=0x04040404,0x02020202,0x02020202,0x010101,0x1ff`
			`temp_add=29767`
			`temp_mult=425`
			`temp_q=10`
			`initxidx2g=45`
			`tssitime=1`
			`rfreg033=0x19`
			`rfreg033_cck=0x1f`
			`cckPwrIdxCorr=-8`
			`spuravoid_enable2g=1`